How To Change Windshield Wipers Honda Accord
The following picture guide goes pace-by-stride on replacing the windshield wiper blades on a Honda Accord.
Check this link for instructions on calculation windshield washer fluid.
This guide covers Honda Accords. The vehicle shown here is a 2004 Accord.
In this guide, we are going to comprehend these steps:
- Selecting the Correct Windshield Wiper Blades
- Removing the Former Wiper Blades
- Install the New Wiper Blades
- Verify the New Bract Installation
Okay, let's go started!
Selecting the Right Windshield Wiper Blades
If y'all are replacing blades on a 2002-2007 Accord, then you demand a 26″ (commuter'southward side) and xviii″ (rider'south side), and the following part numbers volition work for you:
- commuter's side wiper (26″)
- passenger'south side wiper (xviii″)
Some other method is to measure the blades. The connections are fairly standardized these days, then just get the lengths correct, and you have a very good chance of selecting the right ones. Keep in listen that oft the 2 blades (driver'due south and passenger's side) are different lengths, so if you take this arroyo, be sure to measure both.
Remove the Onetime Wiper Blades
Removing the old wiper blades is pretty straightforward. Pull the wiper arm up and abroad from the windshield.
The hardest office is finding the tab that you need to press in social club to release the old bract. The way information technology works is, you lot press the tab, then slide the blade downwards until it is costless of the wiper arm.
This now leaves the wiper arm j-hook exposed. Be careful not to press this arm toward the windshield at this point. Since it is spring-loaded, information technology has the potential to impact the windshield and leave a nick or a crevice! If y'all are worried nearly it, put a towel on the windshield as an added layer of protection.
Install the New Wiper Blades
Nosotros'll now go over how to install the new blades onto the wiper arms. There are several dissimilar types of wiper arms. Hither, we volition discuss the J-hook mounts.
J-Hook Fashion Wiper Arms
Remove the new wiper from the box.
Locate the locking prune on the elevation of the connector. Pry the prune upwardly.
With the locking clip open, inspect the hole where you will insert the j-hook wiper arm.
Line upwardly the wiper arm with the new blade.
Printing the j-claw wiper arm into the pigsty in the wiper blade.
Push the wiper frontwards until you feel a 'click.'
Once the wiper is fully seated on the j-hook, press the locking clip back into place until information technology clicks.
This is the connector once the bract has been fully installed.
We're about done. Carefully slide the protective yellow embrace off of the wiper blade.
These wipers are designed to contour to your windshield. They may look floppy, but that is normal.
Carefully push the wiper arm back toward the windshield until the wiper is contacting the glass.
Repeat the same steps for the rider's side wiper (18″).
Verify the New Blade Installation
That's it! Later you lot take the new blades installed on both wiper arms, get ahead and try them out. Make sure at that place is nothing stuck nether them, and if necessary, wipe a rag along the border to clean them off.
I hope this was helpful!
Here is a link to the wipers I used in this guide, that will work for y'all likewise:
- driver'southward side wiper (26″)
- passenger'due south side wiper (eighteen″)
Thanks for reading! For instructions on calculation windshield washer fluid to your Honda Accord, bank check this link for instructions on adding windshield washer fluid.
For boosted helpful service guides on your Honda Accordance, check out these helpful articles:
Nearly common do-it-yourself Honda Accordance maintenance guides.
Source: https://practicalmechanic.com/2019/08/10/how-to-change-wiper-blades-on-a-honda-accord/
Posted by: amesbeferal.blogspot.com
0 Response to "How To Change Windshield Wipers Honda Accord"
Post a Comment